With patience, the right tools and a friend to help you, hanging drywall is not very difficult.
Tip: Hang plastic sheeting at each door leading to other rooms to trap dust. Also, shut off the air conditioner to avoid getting dust particles in the ductwork and spreading it throughout the house.
Safety: Wear a dust mask and safety glasses to avoid getting dust particles in your lungs and eyes.
Once you’ve hung the drywall, it’s time to finish the joint work. See HomeDepot’s project guides for Taping Joints, Finishing Inside Corners and Finishing Outside Corners for more steps and information about the next phase of your project.
WHAT YOU NEED FOR THIS PROJECT
1 Measure Wall
Measure the width of the wall and cut the sheet so it’s about 1⁄4 inch shorter. Have someone help you position the sheet tight against the ceiling.
2. Add Screws
Begin driving screws in the middle of the panel at a convenient height. Once the first screws are in place, put in the rest, working your way from the center of the panel toward the outside. Drive the screws 16 inches apart, and into all of the studs.
3. Add additional sheets of drywall
Tip: Hanging drywall horizontally can lessen the amount of taping required and place the seam at a convenient height. A longer wall may need more than one sheet of drywall.
Start by hanging a full sheet as before. Tack it in place, and then drive screws every 16 inches and into the studs.
4 Be sure to include cut outs for doors, windows, outlets and other fixtures that appear.
If the sheet covers a window that has yet to be installed:
• Cover the window with a drywall panel and insert a few screws to mark the corners of the future window.
• If you have a drywall router, plunge the router into the approximate center of the window and cut sideways and vertically until you find the edges. If you don’t have a router, use a handsaw.
If the window is in place:
• Take off the window trim and cut the window opening in the drywall sheet before you hang it.
• Lay out the cut by positioning the sheet along the floor and marking where it meets the bottom edge of the window.
• Measure from the ceiling to the window top to lay out the top edge of the cut.
To cut around a door:
• Lay out a door cut the same way as a window.
• Remove the trim. Lean the piece of drywall against the opening, mark the location of the studs, and draw a line for the top of the door opening.
• Make cuts for both doors and windows with a router or drywall saw and screw the panels in place with drywall screws.
To cut for outlets or other wall fixtures:
• Use a spiral saw.
• Note the height of the outlet box or fixture and draw marks on the floor to show where it is.
• Remove the wires and screw the drywall in place, covering the box and driving just enough screws to keep the drywall in place.
• Find the inside edge of the box or fixture by plunging the spiral saw into the box and cutting sideways to the edges in a counterclockwise direction.
Tip: If you are using a hand saw, rub the edges of the outlet box with a dry-erase marker or lipstick and put the drywall panel in place in front of it with two screws for positioning. Rub along the front of the panel where the outlet box is. Then remove the panel and cut along the marks on the back of the panel. Reattach the panel and add drywall screws as necessary.
5. Be sure to install the drywall from the floor to the ceiling and the frames outside corners.
• Begin the bottom row with a shorter piece so that the seam in the top row will not be directly above the seam in the bottom row.
• Position the piece, lift it with a panel lift, and screw it in place. When the small piece is in place, install the longer piece.
Tip: There should be a slight gap between the floor and the drywall so that the drywall won’t jam against bumps in the floor. Baseboard will cover it later. If necessary, trim the sheet to leave about a 1⁄2-inch gap.
When framing outside corners:
• Cut a piece of drywall long so that it hangs over the corner.
• Trim it with a spiral saw after it’s in place.
• Hang the abutting panel, leaving it long, too, and trim it to create a tight, well-fitted corner.
• Protect the corners with metal corner bead. A bead that is a bit long will kink when you fasten it. To prevent this, cut the bead with tin snips, leaving it about 1⁄2 inch short. Hold the bead tight against the ceiling. Screws will distort the bead, so nail it in place, spacing the nails every 9 inches.